Equestrian, Manege & Small-Holding Equipment

A strongly constructed transport box from SCH with tipping facilities.  The tailgate is removable fore ease of emptying and loading.

This SCH plastic bodied tipping trailer runs on large four-stub flotation wheels which are designed for use with an ATV at the extra width of the wheels increases stability at higher speeds. These bearing hubs are able to tolerate tight corners found in stable yards, walled gardens, etc, when fully loaded without damage to the heavy-duty axle. These specially mounted wheels are a must when operating on soft ground conditions or across unfriendly terrain.

The sturdy metal chassis gives superb support to the underside of the rot-proof trailer body.   A manual handle is fitted as standard to assist in manoeuvering the trailer when used away from the towing vehicle (or for hand reversing for those of us who find reversing the tractor or quad impossible!).

The body of the QPTP is moulded from a strong commercial-grade plastic so it will withstand the carting of corrosive material, such as animal waste, without causing body rot.

The QPTP plastic bodied trailer with wide profile wheels is fitted with 50mm ball hitch as standard.

The large plastic trailer fills a gap in SCH's comprehensive trailer range, where a bulk, rot proof, transporter is required. 

The SCH LCPTP is built from tough tear-proof and corrosionn resistant plastic, ideal for corrosive horse muck and garden waste.

The wide profile flotation wheels, on four stud roller bearing hubs, fitted as standard, give the trailer stability over rough or wet ground. The chassis is built of strong steel, giving the plastic body the necessary support. A metal buffer is fitted around the top roll of the trailer.

The trailer tipping device is simple to operate; simply pull the sprung-loaded bolt to allow the trailer to tip. An extendable tipping handle makes the tipping operation an easy task.

The towing hitch is a 50mm ball coupling. Other hitches are available upon request.

This big bale transporter will pick up a bale of up to 1000kg in weight, ready for transportation to the required site. It is equipped with large, low ground pressure wheels which enable it to be towed over unfriendly ground.

Method of Operation:-

• Remove the trailer floor
• Reverse the trailer over the bale
• Lift bale and secure
• Replace floor

British-built by SCH Supplies, the transporter has an overall width of 200cm (80") and an overall length (including tow bar) of 240cm (96cm). It employs a hydraulic manual pump for the lifting jib and is fitted with a 50mm ball towing hitch.

The EPB has been built to reduce the manual collection of horse droppings and improve pasture management.

Suitable for use with most garden tractors and ATVs. Four rows of tough propropelene brushes that can sweep horse droppings, wet / dry grass and leaves. The brush height can be easily adjusted.

The regular removal of droppings promotes healthy grass and helps reduce droppings related diseases. Four rows of height adjustable brushes rotate at variable speeds to flick the droppings into the rot proof rear collecting box. The brushes are driven by a 5.5hp Honda engine equipped with a speed reduction gear box which incorporates a centrifugal clutch, this means when the engine speed is reduced the brushes stop revolving, a necessary feature when moving from heap to heap.

The Equestrian Powered Brush can also be used for other sweeping tasks e.g. car parks etc. The tow hitch is fitted with a 50mm ball hitch.

The unit has four pneumatic wheels; the collection box is made of strong plastic material, mounted on heavy tubular frame, thus making this a durable machine for many years use.

The brushes are easily changed when they become worn.

Optional extras:

• Clevis hitch
• Ball hitch

This collector has been designed specifically by British manufacturer SCH (Supplies) to harvest seeds in wild flower meadows. The brushes are powered by a Honda 5.5hp petrol manual start engine.

The collector drawbar is offset from the pulling vehicle so that the flowers are not flattened before the seeds are collected. The seeds are collected in the integral rear-mounted collection compartment which can easily be emptied via a convenient access door located on the side of the machine. The collected seeds can then be discharged into a bucket or sack by removing the internal drawer.

Featuring a working width of 925mm (37"), the height is adjustable from as low as 150mm (6") up to a maximum of 600mm (24").  A manual hydraulic pump operates a ram mounted at the rear of the unit that allows simple height adjustment.